Calculator

Dump Fee Calculator

Researched November 12, 2026 · sources listed at the end

Dump Fee Calculator

1. Where are you going?

2. What are you hauling in?
3. How full is it?
4. What's in it?
Add Items: Appliances, Mattresses, Tires, TVs
  • Refrigerator or freezer250 lb · EPA 2016 0
  • Clothes washer150 lb · EPA 2016 0
  • Stove150 lb · EPA 2016 0
  • Clothes dryer125 lb · EPA 2016 0
  • Dishwasher125 lb · EPA 2016 0
  • CRT TV over 19 in73 lb · EPA 2016 0
  • Flat-panel TV29 lb · EPA 2016 0
  • Car or light truck tire22.5 lb · EPA 2016 0
  • Mattress, queen hybrid115 lb · Washington Ecology (rough) 0
  • Mattress, queen innerspring100 lb · Washington Ecology (rough) 0
  • Mattress, foam55 lb · Washington Ecology 0
5. A few details

Your loadEstimate

Volume
2.31 yd³
Weight
577 to 692 lb
Tons
0.29 to 0.35

Estimated feePick a site

A level-full 6.5-foot pickup of household junk costs $15 to $34 (the middle half of 502 sites) at the sites we have verified. Pick a location to price your load at a real site.

This dump fee calculator estimates the cost of a self-hauled load from your vehicle, how full it is and what is in it. It converts volume to weight with EPA conversion factors. Then it applies the fee schedule of a real facility near you: the minimum fee, the per-ton or per-load rate, resident pricing and item surcharges. Below the result you'll find how the estimate is calculated, the assumptions, and where every fee comes from.

How Does The Dump Fee Calculator Work?

The calculator estimates your fee in four steps: it measures the load's volume, converts volume to weight by material, applies the facility's fee rules, and adds item surcharges. Each step uses a published source or a dated fee schedule. All of them are listed in the methods panel under the result.

The four steps, in order:

  1. Volume. The bed or trailer size times how full it is gives cubic yards. A 6.5-foot Ford F-150 box holds 62.3 cubic feet, or 2.31 cubic yards, level full1.
  2. Weight. Cubic yards times the material's loose density gives pounds, as a low and high value. EPA puts uncompacted household trash at 250 to 300 pounds per cubic yard2.
  3. Fee rule. The site's posted pricing model turns weight or volume into dollars, with the minimum fee applied (next section).
  4. Surcharges. Per-piece fees for mattresses, tires, appliances and TVs are added on top.

Sometimes a site posts no separate rate for a material in your load. The calculator then uses that site's general trash rate and says so in the result. Sites whose posted fees can't price a load are left out of the list rather than filled in with an average, so every estimate comes from one real fee schedule.

What Formula Do Dumps Use To Charge For A Load?

Most scaled facilities charge the greater of the minimum fee or the net weight in tons times the per-ton rate. Unscaled sites charge per load, per vehicle or per cubic yard instead. The calculator uses whichever model the chosen site posts.

The formulas side by side:

Pricing modelFormula usedIllustration (made-up rates)
Per ton with a minimumFee = the greater of the minimum, or (pounds / 2,000) x rate per ton$50 per ton, $20 minimum: a 600 lb load is $15 by weight, so you pay $20
Per cubic yard with a minimumFee = the greater of the minimum, or cubic yards x rate$15 per cu yd, 2 cu yd minimum: 1.5 cu yd costs $30
Per vehicle or per loadFee = the posted price for your vehicle classOne price for any car, another for any pickup
Flat resident fee or allowanceFee = the flat price, or $0 within the allowance, then the next ruleFree up to an allowance, then per ton

The break-even weight is the point where the per-ton charge passes the minimum: minimum fee divided by the per-ton rate, times 2,000 pounds. With the made-up rates above, that is $20 / $50 x 2,000 = 800 pounds. Below 800 pounds you pay only the minimum. The result card prints this weight for the site you pick, because it tells you whether combining two small trips into one makes sense. For how real sites use each model, and what they charge, see how much the dump costs.

Some sites price construction debris, yard waste and household trash at different rates. At such a site, a mixed load can be priced at the higher rate. Salt Lake County Landfill in Utah, for example, charges $12 per ton for clean broken concrete or asphalt, but a load with prohibited items pays its $36 Mixed Trash rate3. The result says which rate applied. Scale staff classify a load by what is in it.

What Assumptions Does The Estimate Use?

The estimate assumes EPA's loose densities for each material, the bed or trailer volume at the fullness you choose, and the site's fee schedule on its verified date. Wet, packed or unusually dense loads weigh more than the average, so the result is a range rather than one number.

The material densities come from EPA's April 2016 volume-to-weight factors2:

MaterialPounds per loose cubic yardSource
Household trash, uncompacted250 to 300EPA 2016
Mixed construction and demolition debris417EPA 2016
Drywall (gypsum board)467EPA 2016
Asphalt shingles (composition roofing)731EPA 2016
Broken concrete860EPA 2016
Dirt and sand929EPA 2016
Leaves250 to 500EPA 2016
Branches and stumps127EPA 2016
Clean dimensional lumber169EPA 2016
Carpet147EPA 2016

Materials with a single EPA value get a band of 20% either side, marked "assumed ±20%" in the result. Vehicle volumes are measured to the top of the bed sides or trailer walls. A heaped load adds a tapered pile, which we count as half of a full box of that height. Per-piece weights for appliances come from the same EPA document: a refrigerator is 250 pounds and a washer 150 pounds2.

These volumes and weights are the same ones the truck load calculator uses, so the two tools always agree. Use it when you want cubic yards, trip counts or a payload check without a fee.

Where Do The Fees Come From?

Every fee comes from a facility's own posted fee schedule, read on the official page or PDF and dated. The current dataset covers 743 facilities in 49 states, with a median fee age of 7 days (dataset version 2026.11.10).

Fee schedules verified: 743 facilitiesstates: 49median age: 7 daysversion 2026.11.10

Each result links to the exact page or PDF the fee came from. Fees older than a year show an amber "may be out of date" note with the verified date. Our methodology page explains how a fee is read, checked and re-checked, and how to report a change.

Why Might The Real Fee Differ From The Estimate?

The real fee differs when the load is heavier or lighter than the material average, when the site rounds weights or adds an uncovered-load fee, or when staff charge a mixed load at a higher rate. The scale ticket sets the price. The estimate only predicts it.

The common causes, and how to avoid a surprise:

Tick steps as you go. Nothing is saved or sent.

Is A Dump Run The Cheapest Way To Get Rid Of This Load?

A dump run is usually the cheapest paid route for one or two loads, because light loads often pay only the minimum fee. Many trips, a rented truck or a long drive can change that. The result card flags a free option or a cheaper route when your location has one.

Is It Cheaper To Rent A Dumpster Than To Make Several Trips?

Renting a dumpster is cheaper once your trips cost more than a local dumpster. Multiply the per-trip estimate by the trips, add truck rental and fuel, and compare that total with a local dumpster price. The dumpster vs dump run comparison runs this math with the same engine.

What Does A Typical Pickup Load Cost?

A typical pickup load of household junk costs $15 to $34 (the middle half of 502 sites) at the sites we have verified. The dump cost guide shows the median by state and worked examples at real sites.

How Do I Estimate Tons For A Contractor Quote?

Use "I know the weight" or pick the material and volume, then read the tons line in the result. For per-ton rates by state and how they have changed, see our guide to landfill tipping fees.

Sources

  1. Ford Motor Company, "2026 Ford F-150 Pickup Technical Specifications" (03/31/26, V1.1), cargo capacities, https://www.fromtheroad.ford.com/content/dam/fordmediasite/us/en/library/2026/specs/2026_Ford_F150_Specs.pdf, accessed November 12, 2026.
  2. U.S. EPA, "Volume-to-Weight Conversion Factors" (April 2016), https://www.epa.gov/sites/default/files/2016-04/documents/volume_to_weight_conversion_factors_memorandum_04192016_508fnl.pdf, accessed November 12, 2026.
  3. Salt Lake County, "Landfill Pricing" (per-ton rates; no effective date shown), https://www.saltlakecounty.gov/landfill/pricing/, accessed November 12, 2026.